Chap nhan thanh toan
Siêu thị điện máy Bình Minh - Điện máy của mọi nhà
Hotline
SIÊU THI MÁY HÀN
DANH MỤC SẢN PHẨM
Share |
Que hàn gang Philcast Ni

Que hàn gang Philcast Ni

Que hàn gang Philcast Ni

Thông số kỹ thuật


Model: Philcast Ni
Đường kính que hàn: 2.5mm, 3.2mm, 4.0mm, 5.0mm
Chiều dài que: 300mm và 350mm
Hãng sản xuất: Philharc              
Xuất xứ: Philippines

Giá mới: Liên hệ để biết

PHILCAST Ni

AWS Specification: E NiCl

JIS Specification: DFCNi

Other Specification : DIN 8573 : (Eni BG 1)

I. APPLICATIONS:

Repair, reclamation and build-up of cast iron parts, grey cast iron and malleable (blackheat iron) such as auto blocks and heads, cylinder walls, motor exhaust ports, impeller rings, valve seats, cast iron dies, defective castings, gear box housings, pump castings, machine parts, frames, correcting machining errors, joining steel to cast iron, etc.

II. DESCRIPTION:

Shielded Metal Arc Welding electrode used primarily for the reclamation and repair of casting defects, machining errors, shrinkage cavities, gas blow holes and voids resulting from defect excavation of grey iron castings. The electrode is manufactured using a pure nickel core wire and gives a fully machinable weld deposit.

PHILCAST Ni has been specifically designed to produce a very fluid molten pool with good wetting properties making it particularly suitable for the filing of casting defects. An all positional electrode suitable for use with both AC (minimum OCV of 50V) and DC+. Deposit is free from hard zones, cracks and porosity. Low current requirements. Tensile strength and ductility adequate for cast iron.

III. NOTES ON USAGE:

Use  AC or DC+ current. Prior to welding remove all traces of rust, oil, paint, sand inclusions and scale. Use dye penetrant NDT to establish that there are no remaining cracks in shrinkage cavities or blow holes. These defects should be prepared carefully to provide good access for the electrode and to ensure that all contamination is completely removed. Use PHILARC PA-GR gouging/cutting electrodes for the removal of defects and the preparation of the cracked area.

Repairs can be made with or without preheat, this depends upon component size and thickness. For large sections preheating in the region 250ºC-300ºC will facilitate improved machinability of the weld repair. The molten pool exhibits good fluidity which allows the operator to direct the electrode readily into corners whilst filling shrinkage cavities. The slag properties are such that the “slag-over-slag” technique can be applied whilst filling deep blowholes and excavations. Joints or cracks should be grooved if parts are more that 5.0 mm thick till root is 3.25 mm to 5.0mm thick. Use lowest current practical, depositing short intermittent beads about 25mm to 5.0mm. Remove all traces of slag remnants before applying the next bead. Proceed slowly so that the work does not become too hot.

When preheating is required, the whole piece should be kept at a temperature of at least 260ºC. Do not pre-heat only a small part of the job, but keep the whole piece hot. For every heavy castings it is best to cool in sand, asbestos or mica.

     For building up large and deep grooves, the most economical procedure is to use PHILARC PA-52 up to 3.25 mm of the surface to be machined and then finish off with a number Ni.

IV. TYPICAL CHEMICAL COMPOSITION OF WELD METAL (%):

C

Mn

Si

Fe

Ni

0.9

0.27

0.65

0.62

Bal

V. TYPICAL MECHANICAL PROPERTIES OF WELD METAL:

Tensile Strength

N/mm2 (ksi)

Elongation

%

Hardness

HV (HRC)

356 (51.6)

20

140-160 (75-80 HRB)

VI. WELDING POSITIONS: FLAT, FILLET, VERTICAL UP, HORIZONTAL, OVERHEAD

VII. SIZES AVAILABLE AND RECOMMENDED CURRENTS (AC or DC + ):

Size

(mm)

Dia.

2.5

3.2

4.0

5.0

Length

300

350

350

350

Current Range Amp

50-80

70~110

100~140

130~170

Sản phẩm khác
Que hàn chống mài mòn Philhard 610LH, Que hàn  chống mài mòn Philhard 610LH , Mua bán Que hàn  chống mài mòn Philhard 610LH
Giá mới: Liên hệ để biết
Que hàn gang Philcast FeNi, Que hàn điện Philcast FeNi, Bảng giá Que hàn điện Philcast FeNi
Giá mới: Liên hệ để biết
Que hàn đắp Philhard 713, Que hàn điện Philhard 713, Bảng giá Que hàn điện Philhard 713
Giá mới: Liên hệ để biết
Que hàn đắp Philhard 711, Que hàn điện Philhard 711, Bảng giá Que hàn điện Philhard 711
Giá mới: Liên hệ để biết
Hỗ trợ trực tuyến Hanoi
Mr Nam : 0904 499 667
Chat [Mr Nam: 0904 499 667]
Mr Minh : 0932 225 325
Chat [Mr Minh: 0932 225 325]
Ms Yến : 0962208760
Chat [Ms Yến: 0962208760]
Ms Thư : 0903208068
Chat [Ms Thư: 0903208068]
Ms Minh Anh : 0978884915
Chat [Ms Minh Anh: 0978884915]
Ms Thủy : 0936 476 144
Chat [Ms Thủy: 0936 476 144]
Ms Chi : 0912378084
Chat [Ms Chi: 0912378084]
Hỗ trợ trực tuyến HCM
Mr Bình : 0988 764 055
Chat [Mr Bình: 0988 764 055]
Ms Thu Hà : 0904 829 667
Chat [Ms Thu Hà: 0904 829 667]
Ms Hương : 0964 934 177
Chat [Ms Hương: 0964 934 177]
Giỏ hàng của bạn
Đối tác
Hotline
Trực tuyến: 15
Lượt truy cập: 4356682
Copyright © 2009 - 2024 by Binh Minh.
All right reserved

Công ty Cổ Phần Thương mai Dịch vụ và Xuất Nhập Khẩu Bình Minh
Địa chỉ: Số 9,Ngõ 461 Nguyễn Văn Linh, Q. Long Biên, TP.Hà nội
Tel: 024-38751616 và 024-36790555 Hotline: 0904499667
Email: binhminhthuha@gmail.com

============================
Chi nhánh Công ty Cổ Phần Thương mai Dịch vụ và Xuất Nhập Khẩu Bình Minh Tại TPHCM
Địa chỉ: Số 1331/15/144 Đường Lê Đức Thọ,Phường 14, Q. Gò Vấp, TP.Hồ Chí Minh
Tel: 024-38751616 và 024-36790555 Hotline: 0988764055
Email: binhminhthuha@gmail.com

Liên hệ để có giá tốt nhất
Hotlite